Please check your car model and year of manufacture before you place an order with us, thanks!
This electronic throttle controller apply for cars with electronic throttle only. Please make sure your car is Electronic accelerator with plug, our product not support Mechanical accelerator.
FUNCTIONS
The Electronic Throttle Accelerator Controller is a booster which control car throttle open to improve the sensitivity driving experience of the car to adapt to different driving habits and keep in a better driving conditions.Solve the slowly start. Increase the throttle respond speed. Improve the instantaneous acceleration. Decrease engine carbon deposition. Avoid vehicle go forward suddenly. Fuel-efficient. Achieve the best speed rate.
EASY INSTALLATION
Install this throttle accelerator when the car is power off and do as the user manual or installation photo,just plug and play. It takes about 5 minutes to 10 minutes.All adjustment must be in a SAFE driving convenient.
Why should I use electronic throttle controller?
New vehicles are changing every year, mostly because of developments of electronics. Vehicle systems that were mechanically controlled are now controlled by the vehicle’s computer. One such new system is electronic throttle control, known as drive-by-wire.
The drive-by-wire system eliminates the conventional mechanically operated system that had been used since the beginning of the cars. The standard mechanically operated accelerator pedal uses a cable attached from the pedal to the throttle body. When you presses down on the pedal, the cable opens the throttle plate, allowing air to pass through into the engine. The engine RPM is directly proportional to the angle of the throttle plate.
With drive-by-wire, the cable is replaced by an electronically controlled system using advanced electromechanical actuators, In place of a cable, an accelerator pedal position sensor is connected to the accelerator pedal. This sensor,which is a potentiometer, determines the position of the accelerator pedal and signals this information to the vehicle’s ECU, in turn, commands the throttle control motor to open or close the throttle valve.
Do you Feel your gas pedal Sponge ?
The drive-by-wire system has its limitations however, the main problem being that throttle response time is significantly slower. Throttle response, also known as a vehicle’s responsiveness, is a measure of how fast an internal combustion engine can raise its power output from a low RPM to a higher more powerful RPM in response to a driver’s request for acceleration; pushing the pedal down. Throttle response is often jumbled with better power; however throttle response is actually a measurement of the time taken for a change in power output.
Drivers all appreciate the need for speed and thrill of pushing our cars to newer limits, and slower throttle response will just increase the time it takes to get to your vehicle’s max power. To address the problem the aftermarket world has developed a new system to override the factory electronic throttle control settings, which have a noticeable time delay.The Pedal Commander Throttle Controller, is a great addition to add that extra “WOOW” to your drive-by-wire vehicle.
Electronic throttle controller will basically by pass the ECU in the vehicle. The controller is designed to take the information right from the accelerator pedal position sensor and compile it in a high speed controller circuit. It also slightly advances that number and then sends it directly to the ECU. By sending the information to the computer this way a couple of checks can be bypassed that the engine computer will make before sending the signal to open the throttle plate.
With this controller you have 8 different programming options; F1 mode F2 mode F3 mode SON mode LOC mode OOO mode EC Mode OFF mode,In F1 mode F2 mode F3 modeEC mode programming option has 1 to 9 Levels,9 Levels of Acceleration. However the Acceleration will be noticeably faster.
Installation :
1、TURN OFF IGNITION AND WAIT FOR 5 MINUTES:
Power off your vehicle and remove the key, To avoid a “check engine”light,ensure your vehicle has been off for 3-5 minutes before removing the pedal plug.
2、LOCATE PEDAL PLUG:
The accelerator plug is normally on top of your pedal.Carefully unplug the connection from yuor pedal.Take note of the plugs direction/orientation.
3、Connect:
Connect the product cable plug into the female plug you have removed from the pedal,ensure it is in the correct orientation.
4、Insert:
Insert the product female plug into the male accelerator plug.
5、Locate:
Locate the best spot for your new throttle controller,Clean the area with an alcohol wire,peel the backing tape and secure.
Note: If you unplug the accelerator plug too soon you will receive a check engine light as the EUC still has power and is detecting your sensor as defective.Please restart the engine 8 to 10 times the fault will be automatically eliminated.
Reviews
There are no reviews yet.